New Products.

What's New?

Custom Colour 'OZNOZZLE' Kits

 We will build your OZNOS nozzle kit with all the aluminium fittings to 
your choice of colour (from the range listed below) to give that special 
look - to gain show points - or just to be different - colour coordinated 
to match your engine bay or car colour. 





 
Custom PURPLE Nozzle Kit

Choice of Colours:
 Purple
 Pink
 Gold
 Lime
 Black
 Red
Currently our standard 
colours are Blue Nozzles 
with Blue nuts and sleeves 
on the nitrous side and 
Red nuts and sleeves on 
the fuel side of the kit 
- you can also order your 
kit with all Blue fittings.
 
 
Note: You can also send us all the aluminium fittings you have for your 
motor and we will anodize them the same colour - This can also be done to 
your used or second hand fittings on the motor - make it all look new.





 
 Ron's Fuel Injection Systems 




 
 We have been appointed the Australian Distributor for these 'Race Only' 
Methanol fuel injection systems. 
We looked at all the systems available and selected this line of product to 
be used on our new drag race '68 Camaro as we feel that it will deliver more 
power and make the car even quicker.
Methanol also has some inherent advantages:
1. Alcohol burns slower so it doesn't build as much heat each run.
2. It costs less than the dedicated race fuels required in high compression 
 engines.
3. It can be used on any engine with over 10:1 compression ratio.
We carry both the Flying Toilet (black body, single butterfly) and the 
Terminator(blue body, 4 butterfly) in stock.
Both types of systems come complete with everything you need to install them 
onto your engine. The only other items required will be a fuel cell and the 
fuel line to the pump and a return line back to the fuel cell. Check out the 
photos below and you will see how complete the systems are.
The Flying Toilet system sells for $2298.00 including GST and the Terminator 
system sells for $2898.00 including GST.
If you have any questions just email or give us a call and we will be only too 
pleased to assist you.





 
Ron's Famous Flying Toilet   
 
 
 
 
 
 
 
 
 
 
 
 
 





 
 
Ron's Terminator

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
OK. We finally got to put a Ron's Terminator onto our 68 Camaro on a 
Test and Tune day at WSID. That morning we ran the car with the Holley 
Dominator and ran a Personal Best of 8.11 seconds at 166.52 mph. 
Back in the pits we put the Terminator on took it out an hour after the 
first run and ran an 8.16 seconds at 165.07 mph. The air was not quite as 
good with a density altitude just over 100 foot higher.
We are very impressed as we ran the Terminator straight out of the box, 
only adjusting the idle speed prior to the run. 
It took nearly 6 months to get the Dominator to run the 8.11
 





 
 
High Fuel Pressure Nitrous Kits 




 
 We have recently developed 40 psi fuel pressure nitrous kits for late model EFI
vehicles. It is very critical before you buy one of these kits that you have your fuel
rail pressure tested. Fuel delivery to the solenoid must remain above 40 psi at all 
times during a run. 
As with all OZNOS Kits, they have adjustable horsepower settings.
You will find these kits on our price list.
The 80181 kit is a single 'OZNOZZLE' Kit to suit all cars with a single throttlebody. 
The 80182 kit is a twin 'OZNOZZLE' Kit to suit dual throttlebody cars as well the new
GEN III LS1 Holden motor. 
The 80180 and 80182+ kit are add on kits for 80181 and 80182 kit so that they become 
progessive (add horsepower during a run). It is also cheaper to add one of these kits 
than an electronic progression box.
Also to supplement these kits we have a fuel pressure safety switch Part No. 801264,
when fitted, this part will turn your kit off if the fuel pressure drops below 40psi. 
When placing your order advise us of what motor it is going onto and we will supply
the appropriate horsepower jetting.
 
 
 
 
 Fibreglass Panels 




 
 In association with a local fibreglass shop we also have panels to suit '67 to 
'69 Camaro . This includes fenders, 4.5" cowl hood bonnets, (cowl scoop section 
available separately) front spoiler, valance, header panels as well as boot lid, 
bumpers and overriders. 
Prices for these new products are listed on our "Products and Prices Page". 
Fibreglass part numbers from 10000 to 19999.





 
 

 Click here to view the OZRACE FAQ page.  




 
 
 Click here to return to the OZRACE page.